Selecionar um país ou região diferente para visualizar os conteúdos da sua localização.
Estados Unidos da América
07:08:27 GMT+0000 (Coordinated Universal Time)
Informação do produto
Métrico
Imperial
Medidas principales y datos de rendimiento
| B1 | 155 mm | Total Width |
| H | 125 mm | Altura |
| L | 260 mm | Longitud |
Medidas de montaje
| D86 | 95 mm | |
| D87 | 115 mm | Ø Bolt circle |
| d85 | 20 mm | |
| d86 | 76 mm | Ø Inner Fit |
| L88 | 31 mm | |
| G43 | M12 | Thread |
| G87 | M8 | Thread |
| h85 | 60,6 mm | |
| JB43 | 115 mm | |
| JL43 | 180 mm | Tolerance ±0,2 |
| jB8 | 80 mm | |
| NB85 | 6 mm | Width of Keyway |
| NL85 | 25 mm | Length of Keyway |
| NT85 | 3,5 mm | Depth of Keyway |
| T86 | 4 mm | Depth Fit |
| Tol T86 up | 0,5 mm | Upper tolerance |
| Tol T86 low | 0 mm | Lower tolerance |
| t43 max | 24 mm | Depth of Thread |
| t87 max | 15 mm |
Medidas
| B2 | 112 mm | Width of Support Rail |
| B4 | 111 mm | Width of Return Unit |
| B72 | 2 mm | |
| H1 | 70 mm | |
| H2 | 98,6 mm | Altura |
| H4 | 118,3 mm | Height of Return Unit |
| H7 | 65,4 mm | |
| h13 | 25 mm | |
| h14 | 50 mm | |
| L2 max | 8.000 mm | Maximum length of Support Rail |
| L4 | 115,5 mm | |
| L6 | 6 mm | Length of Wiper Brushes |
| S | 85 mm | Medida |
Datos técnicos
| mLAW | 9,06 kg | Mass of Carriage |
| vmax | 8 m/s | Maximum Speed |
| amax | 40 m/s2 | Maximum Acceleration |
| Rx | 120 mm | |
| Ry | 95 mm | |
| Rz | 386 mm | |
| I C | 20.000 N | Load direction I: compressive load |
| I C0 | 10.000 N | Load direction I: compressive load |
| II C | 20.000 N | Load direction II: tensile load |
| II C0 | 10.000 N | Load direction II: tensile load |
| III C | 32.400 N | Load direction III: lateral load |
| III C0 | 18.200 N | Load direction III: lateral load |
| M0x per | 215 Nm | Max. permissible static moment per Carriage 1 |
| M0y per | 1.100 Nm | Max. permissible static moment per Carriage 1 |
| M0z per | 620 Nm | Max. permissible static moment per Carriage 1 |
| Iy | 386 cm4 | Geometrical moments of inertia of Support Rail 2 |
| Iz | 301 cm4 | Geometrical moments of inertia of Support Rail 2 |
Información adicional
1.780 Nm | Max. permissible drive torque | |
4xLFR5302-10-2Z | Track Rollers | |
0,1 mm | Repeat Accurancy ± | |
270 mm | Feed (mm/rotation) | |
32AT10 | Toothed Belt | |
0,2 kg/m | Mass of Toothed Belt | |
1.750 N | Permissible Toothed Belt operating force | |
12,6 kg*cm2 | Mass moment of inertia of Gears |
Rango de temperatura
| Tmin | 0 °C | Minimum operating Temperatur |
| Tmax | 80 °C | Maximum operating Temperatur |
Notas de rodapé
1
The values are single loads and apply when the underside of the actuator is fully supported. If there are several carriage units per actuator or combined loads are present, these must be reduced.
2
Moment of inertia of area of “closed” support rail (= support rail without free milled area on base). In comparison with these values, the moment of inertia of area Iy of the side with the free milled area on the base is reduced to an insignificant degree and the moment of inertia of area Iz is reduced by approx. 10%.
Transferências:
Variante do seu produto atual
| Size code | 52 | |
| Length of carriage | 260 | 260 mm |
| Carriage design | EE | Double strengthened carriage |
| Drive type | (3)ZR | Toothed belt drive |
| Additional carriage | / | No additional carriage |
| Support rail design | / | One-piece |
| Bellow | / | No |